1/35 MSA-0011{Ext} "Ex-S" Full MS Mode [ Version 2.0 ] 全MS形態 [ 升級2.0版 ]
 
 

Original Price $ 2517USD  
Selling Price $2380 USD  
Weight 42.5kg  
Stock Status In stock
Measurment : 55x45x65cm  
We can send it out as soon as you place an order.
We proudly accept PayPal
     
原价: ¥17800 RMB  
售价: ¥15480 RMB  
重量: 42.5kg  
外箱尺寸: 55x45x65cm  
我们乐意接受 淘宝付款 , 收到付款后,立刻安排发货.

淘宝网站 :http://shop35489745.taobao.com

 

 

 

 

 

 

 

 

 

 

Overall height : 125cm
Head height : 94cm
Shoulder width : 66cm
Overall depth : 119cm ( when the tail stabilizer has been stretched )
Kit weight : 42.5 kgs
No. of R2 “Red” resin parts : 21 pcs.
No. of Y1 “Yellow” resin parts : 51 pcs.
No. of B3 “Blue” resin parts : 93 pcs.
No. of W1 “Pure-White” resin parts : 199 pcs.
No. of W2 “Grey-White” resin parts : 12 pcs.
No. of G2 “Medium-Grey” resin parts : 68 pcs.
No. of G3 “Heavy-Grey” resin parts : 308 pcs.
No. of G4 “Dark-Grey” resin parts : 114 pcs.
No. of G5 “Blue-Grey” resin parts : 81 pcs.
No. of S1 “Silver” resin parts : 267 pcs.
No. of clear resin parts : 24 pc.
No. of heat pressed clear parts : 21 pc.
Dark iron coated alluminium-made burners : 4 groups
Basic-coated alluminium-made parts : 233 pcs.
Alluminium tube & rods : 9 pcs.
No. of polycap joints : 48 pcs.
Plastic rod : 1 pc. ( ?5mm x 110mm )
Silver coated copper-made pins : 64 pcs.
No. of spring : 2 pcs. ( ?6 x 80mm ;?8 x 200mm )
No. of steel bearings : 36 pcs. ( ?3 x 3mm x 20 pcs.????5 x 5mm x 16 pcs. )
No. of strip magnets : 14 pcs.
Special weavings : 1 pc. ( ?16mm x 100mm )
Copper rod : 1 pc. (?1 x 90mm)
No. of hexa-screws : 177 pcs.
No. of rubber cord : 2 pcs ( ?5 x 150mm????6 x 200mm )
No. of LED components : LED x 53 / 3.6V 1200mAH Ni-MH Battery x 1 / Recharger x 1 / Band switch x 3 / DC jet / base x 15 / LR41 Batttery x 8
o. of photo etch : 10 pcs
No. of A4 sized water decal sheet : 8 pcs
No. of 4R photos : 3 pcs.

 
 

(1)(2)Full leg is supported internally by a 25x12mm rectangular metal bar at full length 420mm.? It is to support the weight of the leg and the wide open angle of 2 legs (800mm apart).? This also eliminate the need of external support for the legs.? Each leg is made of 204 parts.
(3) Thigh has been lengthen by 30mm.? Width and depth has also been adjusted accordingly.? Stronger lower part can provide greater support for the upper body.
(4) Rich patterns are added to the lower legs.? There are 3 main types repair hatches, total 125 doors on all over the body.? Will show you open hatches mode in the future.
(5) We didn't forget about the Shoe sole, a lot of details and patterns have been added to it.
(6) Light beam sabers on the hip side has been enlarged by 25mm x 10mm.? This is to balance the lengthen legs.
(7) Based on the original design by Katoki, extra components have been added at the back of the hip.? Because of this, the hip has been enlarged by 10mm in length and width.
(8) Behind the knees, it is in fact a large light box.? We attached silver suface gummed paper to increase the reflective effect on the LED built inside.
(9) Sense of depth of the knees are strengthen.? Metal parts are added next to "INCOM" components.
(10) Steel bearing balls are added to the hip side in order to give it a more realistic look.

(11) Full arm is supported internally by metal bar to provide great posting support.? We have added great details and layers to the arms as well.
(12) Forearm armors are re-designed with enhanced details.
(13) Original details are maintained under the forearm.
(14) Shoulder base are constructed by multi-color cast.? We applied magnets to attach the outer blue armors to it.
(15) With lots of metal parts on the shoulder, you will see a more realistic look of the shoulder.
(16) Propellant tank is supported by 4 @5mm metal bars.
(17) Side wings are extendable.? Fully extended length is 415mm.? Normal length is 360mm.? We also added self-contained blinking LED parts (battery, switch and LED) into the wings.
(18), (19) Based on our 1/100 design, the Propellant tank has been added with new patterns and details.
(20) Connectors on the shoulder to the side wings have also been enhanced.
(21) Metal bearing balls are added to the shoulder in order to provide a more realistic look.
(22) Inside the shoulder, you will see 2 giant metallic HYDRAULIC ARMS.? An iconic design of Ex-S.

(23) Cheeks of the head has been thicken and lengthen to lower position of the head.? This produces a clearer outlook of the face.
(24) Tip of the mouth has been shorten and allow more space to expose the nose.? The face is more mask like now.
(25) Wires of the LEDs at the front and from the back are linked together to a single plug for connection to the base at the neck.
(26) Armor at the chest are wide open to show more mechanics.
(27) If you see from the back of the chest, you will see the full mechanics inside it.
(28) When the shoulder connectors are open, you will see massive mechanics connected to those in the chest.
(29) We added large LED at the cockpit.
(30) Lots of details have been added to the air discharge duct of the chest, including fan, metal parts and photo-etch blades.

(31) The burners of core-fighter are made of G-System electroplated plastic.? It carries metal free by itself without painting.
(32) Inside the exhaust of core-fighter, we maintain the original fan design.
(33) The special design re-chargeable battery and power transformer is powerful enough to provide powers to the LEDs for several hours.
(34) We made the main wings based on 1/100 MG Ex-S.? The signal lights are self-powered.? It contains the LED, LR41 battery and on/off switch internally.
(35) Wires handing outside the body are to be connected to the legs and back pack.
(36) Cockpit is open and close like design with moving arms hidden inside.
(37) The empty abdomen is large enough for storing the battery.
(38) The back plate has been re-designed with lots of details.
(39)(40) When you look at the side of the cockpit, you will see lots of details and patterns added to enhance the outlook.
(41) When charging is required, remove the small armour and plug in the charger.
(42) We added lots of details into the shoulder hinge.

(43) The Beam Smartgun is made of 66 multi-color cast.
(44) The monitoring disc has built-in LED.? Wires are connected to the main body of the SmartGun.
(45) When you look at the side of the gun, you will see wires on the top for connecting the monitoring disc.? The wires below are for the power source from the Ex-S body.
(46) Power wires are 18mm silver white weaves based on the original design.? If it was soaked in grey color, the effect will be much better.
(47) At the end of the Beam Smartgun, we reserved space for the photo-etch to show a more realistic look.
(48) New layers of details are added to both side of the Beam Smartgun.
(49) Springs are added to the tip of the Beam Smartgun.


 

 

全高:125cm
頭頂高:94cm
肩寬:66cm
全深:119cm (當尾鰭展開時)
激光槍全長:98cm
本體重量:30.5 kgs
產品毛重:42.5 kgs
R2專用紅色樹脂部件:21件
Y2專用黃色樹脂部件:51件
B3專用藍色樹脂部件:93件
W1純白色樹脂部件: 199件
W2淺灰白色樹脂部件: 12件
S1加工銀色樹脂部件:267件
G3深灰色樹脂部件:308件
G2中灰色樹脂部件:68件
G4灰黑色樹脂部件:114件
G5專用灰藍色樹脂部件:81件
PVC空心搪膠部件:37件 (白色32件; 灰黑色5件)
透明焗瓷配件:24件
透明吸塑配件:21件
黑鐵色電鍍塑膠啤注火箭噴射筒:4組
原色鋁合金零件:233件
鋁合金圓柱 / 圓管:9件
軟膠關節配件:48件
圓形膠支:1條 (?5mm x 110mm)
電鍍銀針:64件
彈簧 : 2條 (?6 x 80mm ;?8 x 200mm)
走珠 : 36粒 (?3 x 3mm x 20粒;?5 x 5mm 16粒)
方形磁鐵 : 14塊
織繩 : ?16mm x 1條
銅支 : 1條 (?1 x 90mm)
杯頭螺絲 : 177杖
軟膠喉管:2條 (?5 x 150mm;?6 x 200mm)
LED發光裝置:LED燈 x 53|3.6V 1200mAH充電式鋰電池 x 1|專用充電器 x 1|波段開關 x 3|DC插/座 x 15|LR41電池 x 8
攝影蝕刻片:10件
A4專用水貼 : 8 張
4R產品照片 : 3 張

 
     
     

(1)(2)整條腿中央由25X12MM方形鋁槽貫穿,全長420MM,用以維持大腿、小腿、及腳掌的永久性固定及兩腿預設的張開角度(兩腿相距800MM),並省卻以外物支撐腳底的需要。膝位置已預留插孔以備接合主膝裝配位伸出的插頭
(3)大腿比2003年舊作已經延長了30MM,而寛度及厚度亦按比例作出了相應的修改。增肥後的大腿有利承托上身,改善模型整體的視覺協調
(4)小腿兩側重新揉造豐富的花紋。當中雕刻的維修用小門的機械結構,全身大大小小共設有三款,合共125個,下期還會展示裝上蝕刻片製小門打開後的姿態
(5)容易被忽略的鞋底也一絲不苟,重新塑造豐富的雕刻,提升平面單調的立體感
(6)腰間兩側的激光槍,被徹底分件及偷空。而且整體長度也被延長了25MM;寛度給增加了10MM,以配合被增長了的雙腿之比例
(7)根據KATOKI的原設定案,褲襠背部給追加了額外的組件。由於HIP位給增豐了,所以褲檔的高度、寛度和邊沿都給增了10MM
(8)打開主膝組件,內部其實是一個大型燈箱,上面預貼了銀面膠紙(文具店有售),以增強反光效果。LED則裝在燈箱的上下兩端
(9)主膝前端增設了一個鈎型配件,以加強其層次感。INCOM組件兩旁加裝了金屬配件
(10)主褲頭中央開穿了方形大洞,以備方形鋁槽插入連接左右兩腿?褲頭側的圈圈裝上了鋼造走珠以提升現實感?整個腳部基本由204件多色成形樹脂部件組成。

(11) 手臂由整條內骨貫通,並且比舊作增強了層次感及細部雕刻。外甲只需要簡單沿着內骨的方形定位裝上便可
(12) 前臂外裝甲同為重新製作,上面被加了豐富的DETAILS
(13) 前臂背底的保留了原有的細節
(14) 在裝上藍色外甲前的肩膞部份,由若干多色樹脂板塊搭建組成。當中還採用了2個方形磁鐵、1個環形磁鐵以固定藍色外甲
(15) 安裝上大大小小的金屬部件後,肩膞整體的現實感更加顯著
(16) 燃料筒的接臂用了4條?5MM的金屬支作接合
(17) 肩翼可以作伸縮活動。展開時的總長為415MM,收納時為360MM。翼上的LED訊號燈可自給自足,即電池、開關、LED三者盡在一個部件內完成。設計上是閃燈設計
(18),(19) 續航燃料筒上被重刻劃上全新設計的花紋,基本上沿用G-SYSTEM 同款1/100的設計再追加上若干細節
(20) 肩上連合肩翼的連接臂架及附近的細部同樣被優化了
(21) 腋窩下的機械組件給裝上了鋼造走珠以提升現實感
(22) 肩內位置兩條特粗油壓臂乃EX-S的代表ICON

(23)新舊版正面的對比:面頰左右兩側已大幅度地補厚了,而兩腮板亦伸延至較低的地方,使整個面罩的輪廓變得清楚
(24)嘴巴及鼻樑經過重新的部署︰嘴巴的末端給改短了,上方亦被殺低了很多,使鼻樑部份重新展露,重現面罩的感覺
(25)頭冠前方及後方的LED連線到專用接頭,以便插接到頸部的底座。
(26)藍色胸甲開設了特大的門洞,充份展露內部完整的機械組件
(27)從胸口背後可以看到內部機械的一體結構
(28)未裝上頂蓋的肩帶內部藏有粗大的機械組件,一直連接到前方胸口的機械部份
(29)駕駛倉前方開設了特大LED電飾裝置
(30)未裝上蝕刻片之前,可以清楚透視到排氣槽內的情況,當中的圓形位置也給挖空裝上風車及金屬配件

(31)核戰底部的火箭噴射筒乃採用G-SYSTEM專用的注塑電鍍啤膠配件,不用上色自身都帶有金屬效果
(32)核戰機排氣葉內隴仍保留舊作的風車組件
(33)本PROJECT的專用充電式鋰電池及充電器(火牛),特別設計以帶動48個各的LED發光燈泡,作維持數小時之久(詳情請參考本貨品的組合說明)
(34)首次亮相的一對主機翼,外形參考我們的1/100同款MG模型改件產品製作。兩側機翼訊號燈乃自給自足的LED裝置,內隴已藏有LED、LR41電池、接觸片及開關
(35)上身背板中央是背包電飾連接的底座所在,圖中所見仍未裝上蝕刻片及維修小門。拉伸出來的電線其實是連接背包及腿部LED的電線
(36)駕駛倉上蓋乃開合式的設計,以多塊蝕刻片組叠使用作活動臂,並以螺絲收緊,可以作超大角度的翻揭
(37)肚兜特大內部空間藏有本製品之專用鋰電池
(38)背板給重新加工製作並作了多色成形分件處理
(39)(40)從側旁角度觀賞,可以清楚看到駕駛倉及肚兜表面被追加了豐富的細部雕刻。按照EX-S的補充資料,肚兜邊沿加接一層機械板塊,不像舊作般直插到核戰機內
(41)充電時需要把充電插頭插到肚兜前方的設定插孔,完成後把有關組件重新放上以摭蔽
(42)肩帶上蓋可作有限度的翻揭,可隱約透視到內隴的機械情況,引人入勝。

(43) 用激光槍由66件多色成形樹脂部件組成
(44) 飛碟型觀察器內藏LED及電線,通過後方掛臂連接到槍身
(45) 激光槍的橫切面:上部電線乃用作連接飛碟型觀察器及描準器,通過接頭連接下方掛架。而掛架的底部亦設定了另一插頭,以連接褲頭電源
(46) 能源管乃?18MM粗的銀白色線質織帶,以體現原設定的應有神髓。如果把它用水彩染成灰色才使用,效果應會更佳
(47) 為了增強表現槍砲的現實感,槍柄後部故意預留了坑槽以放上蝕刻片,以蝕刻字重現應有的浮雕感
(48) 槍身兩邊夾着槍管的長板鋪設了層板作浮雕,改善平板單調的問題
(49) 槍咀按照原設定裝上兩條彈簧


 

 

 

 

 

G-System-Best All Rights Reserved @2008,New Genesis Gundam Models , 粤ICP备09039651号

邮箱 E-Mail: gsb368@163.com , E-mail: info@g-system-best.com